Ductwork & Airflow Services, Georgetown TX
Duct Repair & Construction
Repair disconnected, damaged, or collapsed duct sections. Restore airflow to rooms losing conditioned air.
Professional duct sealing with mastic or foil tape, eliminate air leaks that waste conditioned air in attic and crawlspace.
New duct system design and installation for additions, renovations, or full system replacement.
Custom fabrication of sheet metal trunk lines, branches, and fittings for high-performance duct systems.
Splice and reconnect flex duct sections, replace damaged sections, and correct improper flex duct installations.
Custom supply plenum fabrication for equipment replacements where the new unit requires a different plenum configuration.
Repair leaking or damaged return air plenums that allow unconditioned attic air to enter the system.
Applied mastic sealing for all duct joints and connections, the most durable sealing method for Georgetown's attic conditions.
Seal duct boots at registers where leakage directly into walls or ceilings causes significant energy loss.
Airflow Balancing
Measure and balance air distribution across all supply and return vents for even comfort throughout the home.
Comprehensive whole-house airflow evaluation and adjustment, dampers, registers, and duct sizing evaluated.
Balance airflow to specific problem rooms that receive too much or too little conditioned air.
Adjust zone dampers and control settings for homes with zoning systems to improve comfort and efficiency.
Full optimization of multi-zone airflow systems, control logic, damper travel, and zone sizing.
Optimize how conditioned air is distributed throughout the duct system for efficiency and comfort.
Improve overall air movement in the home through duct, register, and equipment adjustments.
Undersized return air is the most overlooked duct problem, we measure and correct return air flow.
Expand or add return air drops to improve system static pressure and airflow in homes with insufficient return capacity.
Dampers & Registers
Install manual balancing dampers in branch ducts to control airflow to specific zones or rooms.
Repair or replace motorized zone dampers that are stuck open, stuck closed, or not responding to controls.
Replace damaged, rusted, or improperly sized floor registers and diffusers.
Replace ceiling supply and return grilles with correct sizing and airflow direction for your room layout.
Install transfer grilles to improve pressure equalization and airflow between rooms with closed doors.
Install jump ducts above doorways or through walls to allow air pressure equalization between zones.
Redirect or baffle supply vents that blow directly on occupants or create drafty areas.
Measure and calibrate airflow from each vent against design specifications.
Ventilation & Testing
Repair ERVs, HRVs, exhaust fans, and dedicated ventilation systems.
Improve fresh air exchange and indoor air quality through targeted ventilation upgrades.
Measure system static pressure to identify duct restrictions causing equipment stress and efficiency loss.
Isolate duct sections from structure to eliminate vibration noise that transmits through walls and ceilings.
Install internal duct lining to absorb noise from high-velocity air movement in ducts near occupied spaces.
Duct Insulation & Protection
Install or replace duct insulation in Georgetown attics where heat gain from uninsulated ducts wastes significant energy.
Install vapor barriers to prevent condensation on cold supply ducts in Georgetown's humid summers.
Support or repair duct systems during crawlspace encapsulation projects.
Repair small-diameter high-velocity duct systems found in older homes and historic properties.
Improving Overall Air Movement
Air circulation improvement addresses the broader feel of stale, stagnant, or uneven air movement throughout a home, which can stem from several different causes working together rather than a single isolated defect. Common contributors include registers positioned poorly relative to the room's furniture layout or ceiling height, an undersized or improperly located return grille that limits how much air the system can actually pull back for reconditioning, blocked or partially closed supply vents behind furniture, and duct runs that deliver adequate volume but poor throw distance, meaning the air reaches the room but does not actually mix with the room's air mass effectively.
Our approach starts with a room-by-room walkthrough checking register condition, damper position, and any physical obstructions, since we regularly find registers with dampers closed from a previous occupant's preference or furniture blocking more than half the register opening. We then evaluate register type and placement against the room's use, since a high sidewall register throwing air across a room with a low ceiling behaves very differently than the same register in a room with an 9 or 10 foot ceiling, and a poor match between register style and room geometry can leave air pooling in one area while another feels stagnant regardless of total airflow volume.
In Georgetown's open-concept floor plans, common in homes built over the last two decades, air circulation issues often show up as a large great room where the area near the kitchen feels fine but a reading nook or corner far from any register feels stuffy, since large open spaces distribute air less predictably than a series of smaller enclosed rooms. We address this with a combination of register redirection using adjustable louvers or baffles, adding or relocating return air paths to improve circulation back through the system, and in some cases recommending a ceiling fan or a small booster fan for a specific dead zone that duct modification alone would not economically resolve. A circulation improvement visit typically runs 200 to 500 dollars depending on the number of rooms assessed and adjustments made.
Frequently Asked Questions, Air Circulation Improvement
Uneven Comfort or High Energy Bills?
Ductwork problems are often the hidden cause. We diagnose and fix them.