Ductwork & Airflow Services, Georgetown TX
Duct Repair & Construction
Repair disconnected, damaged, or collapsed duct sections. Restore airflow to rooms losing conditioned air.
Professional duct sealing with mastic or foil tape, eliminate air leaks that waste conditioned air in attic and crawlspace.
New duct system design and installation for additions, renovations, or full system replacement.
Custom fabrication of sheet metal trunk lines, branches, and fittings for high-performance duct systems.
Splice and reconnect flex duct sections, replace damaged sections, and correct improper flex duct installations.
Custom supply plenum fabrication for equipment replacements where the new unit requires a different plenum configuration.
Repair leaking or damaged return air plenums that allow unconditioned attic air to enter the system.
Applied mastic sealing for all duct joints and connections, the most durable sealing method for Georgetown's attic conditions.
Seal duct boots at registers where leakage directly into walls or ceilings causes significant energy loss.
Airflow Balancing
Measure and balance air distribution across all supply and return vents for even comfort throughout the home.
Comprehensive whole-house airflow evaluation and adjustment, dampers, registers, and duct sizing evaluated.
Balance airflow to specific problem rooms that receive too much or too little conditioned air.
Adjust zone dampers and control settings for homes with zoning systems to improve comfort and efficiency.
Full optimization of multi-zone airflow systems, control logic, damper travel, and zone sizing.
Optimize how conditioned air is distributed throughout the duct system for efficiency and comfort.
Improve overall air movement in the home through duct, register, and equipment adjustments.
Undersized return air is the most overlooked duct problem, we measure and correct return air flow.
Expand or add return air drops to improve system static pressure and airflow in homes with insufficient return capacity.
Dampers & Registers
Install manual balancing dampers in branch ducts to control airflow to specific zones or rooms.
Repair or replace motorized zone dampers that are stuck open, stuck closed, or not responding to controls.
Replace damaged, rusted, or improperly sized floor registers and diffusers.
Replace ceiling supply and return grilles with correct sizing and airflow direction for your room layout.
Install transfer grilles to improve pressure equalization and airflow between rooms with closed doors.
Install jump ducts above doorways or through walls to allow air pressure equalization between zones.
Redirect or baffle supply vents that blow directly on occupants or create drafty areas.
Measure and calibrate airflow from each vent against design specifications.
Ventilation & Testing
Repair ERVs, HRVs, exhaust fans, and dedicated ventilation systems.
Improve fresh air exchange and indoor air quality through targeted ventilation upgrades.
Measure system static pressure to identify duct restrictions causing equipment stress and efficiency loss.
Isolate duct sections from structure to eliminate vibration noise that transmits through walls and ceilings.
Install internal duct lining to absorb noise from high-velocity air movement in ducts near occupied spaces.
Duct Insulation & Protection
Install or replace duct insulation in Georgetown attics where heat gain from uninsulated ducts wastes significant energy.
Install vapor barriers to prevent condensation on cold supply ducts in Georgetown's humid summers.
Support or repair duct systems during crawlspace encapsulation projects.
Repair small-diameter high-velocity duct systems found in older homes and historic properties.
How We Target Specific Problem Rooms
Multi-room balancing focuses on a defined set of problem areas, typically two to four rooms that a homeowner has identified as consistently too hot, too cold, or too stuffy, rather than a full-home assessment of every register. This targeted approach makes sense when most of the house is comfortable and only specific rooms stand out, which usually points to a localized cause: a branch damper that has drifted closed, a takeoff sized for a smaller room that was later converted to a different use, or a duct run with more bends and length than the rest of the system.
We begin by measuring airflow at the problem registers and comparing them against neighboring rooms of similar size and use, which quickly shows whether the issue is a flow deficit specific to that room or a broader system limitation. From there we trace the branch duct back toward the trunk line, checking for kinks, excessive length, or a damper position that does not match its labeled setting. A common finding in Georgetown homes is a bedroom over a garage or at the end of a long branch run that was under-designed relative to its actual heat gain, since garages transmit more heat into the room above than the original load calculation may have assumed, especially in homes without insulated garage ceilings.
Correcting the imbalance sometimes means opening a damper fully and closing back nearby overserved rooms slightly to compensate, and sometimes it means the branch itself needs modification, a shorter run, fewer bends, or a larger diameter takeoff, if damper adjustment alone cannot deliver enough air to that specific room. We measure before and after every adjustment so we know the fix actually worked rather than assuming it based on the change made. Multi-room balancing for a handful of target rooms typically runs 200 to 400 dollars and can usually be completed in a single 2 to 3 hour visit.
Frequently Asked Questions, Multi-Room Airflow Balancing
Uneven Comfort or High Energy Bills?
Ductwork problems are often the hidden cause. We diagnose and fix them.