HVAC Components We Repair & Replace, Georgetown TX
Motors & Fans
Diagnose and repair indoor blower motor failures, bearing wear, winding failure, and capacitor issues.
Replace failed indoor blower motors, we stock common motors for Carrier, Trane, Lennox, Goodman, and Rheem.
Lubricate blower motor bearings before they fail, catches motors that squeal before they burn out.
Clean blower wheels coated with dust and debris that reduce airflow and strain the motor.
Repair or replace condenser fan motors, outdoor fan failure causes compressor overheating on Georgetown's 100°F days.
Diagnose and repair outdoor condenser fan motor failures, common cause of AC shutdown in peak summer heat.
Replace cracked, bent, or imbalanced outdoor fan blades causing vibration and motor strain.
Capacitors & Contactors
The #1 Georgetown summer repair. Capacitors overheat and fail in sustained 100°F+ heat, fast, affordable fix.
Test capacitors before replacing, an out-of-spec capacitor causes the same symptoms as a failed compressor.
Replace failed run capacitors on compressors and fan motors, the most common summer AC component failure.
Replace start capacitors that provide the extra torque needed to start compressors on hot days.
Install hard start kits on aging compressors to reduce starting current and extend compressor life.
Replace pitted or failed contactors, the relay that connects power to the compressor and condenser fan.
Replace AC contactors with pitted contacts that cause intermittent power to compressor and outdoor fan.
Compressor Service
Diagnose compressor failures, not every compressor problem requires replacement. We test before recommending replacement.
Compressor replacement with full circuit flush, filter drier, evacuation, and recharge, done correctly to protect the new compressor.
Replace discharge mufflers that reduce compressor noise and protect the refrigerant circuit.
Install crankcase heaters to prevent refrigerant migration into compressor oil during cold Texas nights.
Replace failed high-pressure safety switches that protect compressors from dangerously high discharge pressure.
Replace low-pressure safety switches that prevent compressor damage from loss of refrigerant charge.
Furnace Components
Replace failed high-limit switches that shut furnaces down on overheating, essential safety component.
Replace faulty furnace control boards, we test all connected components first to confirm the board is the failure.
Repair or replace fan control switches that govern blower timing in older furnaces without electronic control boards.
Replace fragile silicon carbide or silicon nitride ignitors, the #1 furnace no-heat repair in Georgetown.
Replace or clean flame sensors that fail to detect the burner flame, causing furnace lockout.
Replace failed gas valves that prevent gas flow to burners, verified diagnosis before replacement.
Replace thermocouples on older standing pilot furnaces that fail to keep the pilot lit.
Replace tripped rollout switches, but also diagnose why flames rolled out, as this indicates a serious underlying condition.
Replace failed draft inducer motors in 80%+ efficiency furnaces, failure causes pressure switch trips and no-heat conditions.
Replace failed heating elements in electric furnaces, test all elements and sequencers before partial replacement.
Replace failed sequencers that stagger heating element startup to prevent circuit overload.
Replace cracked or blocked pilot tubing on older standing pilot furnaces and boilers.
Repair standing pilot assembly issues on older furnaces, thermocouple, pilot orifice, and gas valve.
Replace corroded or leaking main gas shutoff valves at HVAC equipment.
Outdoor Unit & Noise Components
Install compressor sound blankets to reduce outdoor unit noise, particularly useful in Georgetown's zero-lot-line neighborhoods.
Replace deteriorated equipment pads and isolation mounts that transmit vibration through slabs and walls.
Keeping Compressor Vibration Out of Your Home
Vibration isolation pads sit between your outdoor condensing unit's base and the concrete pad or ground beneath it, and their job is to absorb the mechanical vibration produced by the compressor and fan motor rather than letting it transmit directly into the slab, and from the slab into the structural framing of the house. On homes built close together or with the unit positioned near a bedroom wall, poor vibration isolation can turn a normally quiet system into a noticeable low frequency hum felt through the floor as much as heard.
Most residential units use simple rubber or neoprene composite pads under each corner or foot of the unit's base rail. These materials are chosen for their damping properties, but rubber and neoprene both degrade over time from prolonged UV exposure, ozone exposure from the compressor's own electrical components, and the constant compressive load of the unit's weight. Degraded pads compress unevenly, harden, or crack, which reduces their damping effectiveness and can also leave the unit sitting slightly unlevel, adding stress to the compressor's internal components over years of operation.
On some installations, particularly larger residential or light commercial compressors, spring type isolators are used instead of solid rubber pads for more effective vibration control at lower frequencies. We inspect whichever isolation method your system was originally installed with and replace it in kind, matching the load rating to your unit's weight rather than installing a generic pad that may be undersized for a larger residential condenser.
When we replace isolation pads, we also recheck that the unit is sitting level on its pad, an unlevel condenser can cause improper oil return within the compressor over time and contributes to premature bearing wear in the fan motor. This is a relatively low-cost repair item, but it's one that's easy to overlook until a homeowner notices a change in operating noise or feels vibration transmitted into an adjacent room.
Georgetown's clay-heavy soil in many neighborhoods causes slabs and pads to shift slightly with seasonal moisture swings between our dry summers and wetter spring months, which can accelerate uneven pad compression compared to a home on more stable soil, making periodic isolation pad inspection worthwhile even on units that otherwise seem to be running fine.
Frequently Asked Questions, AC Vibration Isolation Pad Replacement
Need a Component Diagnosed or Replaced?
We test before we replace. Most parts are on the truck for same-day service.