HVAC Components We Repair & Replace, Georgetown TX
Motors & Fans
Diagnose and repair indoor blower motor failures, bearing wear, winding failure, and capacitor issues.
Replace failed indoor blower motors, we stock common motors for Carrier, Trane, Lennox, Goodman, and Rheem.
Lubricate blower motor bearings before they fail, catches motors that squeal before they burn out.
Clean blower wheels coated with dust and debris that reduce airflow and strain the motor.
Repair or replace condenser fan motors, outdoor fan failure causes compressor overheating on Georgetown's 100°F days.
Diagnose and repair outdoor condenser fan motor failures, common cause of AC shutdown in peak summer heat.
Replace cracked, bent, or imbalanced outdoor fan blades causing vibration and motor strain.
Capacitors & Contactors
The #1 Georgetown summer repair. Capacitors overheat and fail in sustained 100°F+ heat, fast, affordable fix.
Test capacitors before replacing, an out-of-spec capacitor causes the same symptoms as a failed compressor.
Replace failed run capacitors on compressors and fan motors, the most common summer AC component failure.
Replace start capacitors that provide the extra torque needed to start compressors on hot days.
Install hard start kits on aging compressors to reduce starting current and extend compressor life.
Replace pitted or failed contactors, the relay that connects power to the compressor and condenser fan.
Replace AC contactors with pitted contacts that cause intermittent power to compressor and outdoor fan.
Compressor Service
Diagnose compressor failures, not every compressor problem requires replacement. We test before recommending replacement.
Compressor replacement with full circuit flush, filter drier, evacuation, and recharge, done correctly to protect the new compressor.
Replace discharge mufflers that reduce compressor noise and protect the refrigerant circuit.
Install crankcase heaters to prevent refrigerant migration into compressor oil during cold Texas nights.
Replace failed high-pressure safety switches that protect compressors from dangerously high discharge pressure.
Replace low-pressure safety switches that prevent compressor damage from loss of refrigerant charge.
Furnace Components
Replace failed high-limit switches that shut furnaces down on overheating, essential safety component.
Replace faulty furnace control boards, we test all connected components first to confirm the board is the failure.
Repair or replace fan control switches that govern blower timing in older furnaces without electronic control boards.
Replace fragile silicon carbide or silicon nitride ignitors, the #1 furnace no-heat repair in Georgetown.
Replace or clean flame sensors that fail to detect the burner flame, causing furnace lockout.
Replace failed gas valves that prevent gas flow to burners, verified diagnosis before replacement.
Replace thermocouples on older standing pilot furnaces that fail to keep the pilot lit.
Replace tripped rollout switches, but also diagnose why flames rolled out, as this indicates a serious underlying condition.
Replace failed draft inducer motors in 80%+ efficiency furnaces, failure causes pressure switch trips and no-heat conditions.
Replace failed heating elements in electric furnaces, test all elements and sequencers before partial replacement.
Replace failed sequencers that stagger heating element startup to prevent circuit overload.
Replace cracked or blocked pilot tubing on older standing pilot furnaces and boilers.
Repair standing pilot assembly issues on older furnaces, thermocouple, pilot orifice, and gas valve.
Replace corroded or leaking main gas shutoff valves at HVAC equipment.
Outdoor Unit & Noise Components
Install compressor sound blankets to reduce outdoor unit noise, particularly useful in Georgetown's zero-lot-line neighborhoods.
Replace deteriorated equipment pads and isolation mounts that transmit vibration through slabs and walls.
The Older Motors That Actually Need Annual Oiling
Not every blower motor is sealed for life. Many older PSC blower motors, particularly ones original to systems installed before the mid-2000s, use sleeve bearings rather than sealed ball bearings, and sleeve bearing motors are designed with small oil ports built into the motor housing specifically so a technician can add a few drops of non-detergent 10-weight electric motor oil once a year to keep the bearing surfaces lubricated. Newer ECM motors and most modern PSC motors use permanently sealed ball bearings that require no maintenance lubrication at all, so the first step in this service is always confirming which type of motor you actually have.
When a sleeve bearing motor's oil ports are neglected for years, the bearing surface gradually dries out, and friction between the shaft and bearing increases. This shows up first as a faint squeal or chirp on startup that fades once the motor warms up, then progresses to a continuous grinding or squealing noise as bearing wear worsens, and eventually to a seized bearing that stops the motor from turning at all, at which point lubrication can no longer help and the motor requires full replacement.
Our lubrication service involves locating the oil ports, which are typically small rubber or metal caps on each end of the motor housing, cleaning around them to prevent dirt or dust from getting introduced into the bearing along with the oil, and applying the correct amount and type of oil, too much oil can actually attract dust and debris that then works its way into the bearing and accelerates wear rather than preventing it. We also check belt tension and motor mount condition on units where applicable, since a misaligned or overly tight belt can put lateral stress on the bearing that lubrication alone won't solve.
This is a preventive service that makes the most sense caught early, once a bearing has progressed to loud grinding or visible shaft play, oiling it typically only delays the inevitable by weeks rather than restoring the bearing to good condition. For a motor still in its early squeal stage, though, a simple annual oiling as part of seasonal maintenance can meaningfully extend the working life of an otherwise good motor, which matters given how hard Georgetown's attic heat already works these motors during our long cooling season.
Frequently Asked Questions, Blower Motor Bearing Lubrication
Need a Component Diagnosed or Replaced?
We test before we replace. Most parts are on the truck for same-day service.