HVAC Components We Repair & Replace, Georgetown TX
Motors & Fans
Diagnose and repair indoor blower motor failures, bearing wear, winding failure, and capacitor issues.
Replace failed indoor blower motors, we stock common motors for Carrier, Trane, Lennox, Goodman, and Rheem.
Lubricate blower motor bearings before they fail, catches motors that squeal before they burn out.
Clean blower wheels coated with dust and debris that reduce airflow and strain the motor.
Repair or replace condenser fan motors, outdoor fan failure causes compressor overheating on Georgetown's 100°F days.
Diagnose and repair outdoor condenser fan motor failures, common cause of AC shutdown in peak summer heat.
Replace cracked, bent, or imbalanced outdoor fan blades causing vibration and motor strain.
Capacitors & Contactors
The #1 Georgetown summer repair. Capacitors overheat and fail in sustained 100°F+ heat, fast, affordable fix.
Test capacitors before replacing, an out-of-spec capacitor causes the same symptoms as a failed compressor.
Replace failed run capacitors on compressors and fan motors, the most common summer AC component failure.
Replace start capacitors that provide the extra torque needed to start compressors on hot days.
Install hard start kits on aging compressors to reduce starting current and extend compressor life.
Replace pitted or failed contactors, the relay that connects power to the compressor and condenser fan.
Replace AC contactors with pitted contacts that cause intermittent power to compressor and outdoor fan.
Compressor Service
Diagnose compressor failures, not every compressor problem requires replacement. We test before recommending replacement.
Compressor replacement with full circuit flush, filter drier, evacuation, and recharge, done correctly to protect the new compressor.
Replace discharge mufflers that reduce compressor noise and protect the refrigerant circuit.
Install crankcase heaters to prevent refrigerant migration into compressor oil during cold Texas nights.
Replace failed high-pressure safety switches that protect compressors from dangerously high discharge pressure.
Replace low-pressure safety switches that prevent compressor damage from loss of refrigerant charge.
Furnace Components
Replace failed high-limit switches that shut furnaces down on overheating, essential safety component.
Replace faulty furnace control boards, we test all connected components first to confirm the board is the failure.
Repair or replace fan control switches that govern blower timing in older furnaces without electronic control boards.
Replace fragile silicon carbide or silicon nitride ignitors, the #1 furnace no-heat repair in Georgetown.
Replace or clean flame sensors that fail to detect the burner flame, causing furnace lockout.
Replace failed gas valves that prevent gas flow to burners, verified diagnosis before replacement.
Replace thermocouples on older standing pilot furnaces that fail to keep the pilot lit.
Replace tripped rollout switches, but also diagnose why flames rolled out, as this indicates a serious underlying condition.
Replace failed draft inducer motors in 80%+ efficiency furnaces, failure causes pressure switch trips and no-heat conditions.
Replace failed heating elements in electric furnaces, test all elements and sequencers before partial replacement.
Replace failed sequencers that stagger heating element startup to prevent circuit overload.
Replace cracked or blocked pilot tubing on older standing pilot furnaces and boilers.
Repair standing pilot assembly issues on older furnaces, thermocouple, pilot orifice, and gas valve.
Replace corroded or leaking main gas shutoff valves at HVAC equipment.
Outdoor Unit & Noise Components
Install compressor sound blankets to reduce outdoor unit noise, particularly useful in Georgetown's zero-lot-line neighborhoods.
Replace deteriorated equipment pads and isolation mounts that transmit vibration through slabs and walls.
Every Type of Capacitor in Your HVAC System
When people say capacitor replacement, they usually mean the AC's run capacitor, but capacitors are used throughout an HVAC system wherever a single phase motor needs help maintaining a rotating magnetic field for starting torque and running efficiency. That includes the outdoor condenser and compressor motors, the indoor blower motor if it's a PSC type, and the draft inducer motor on many gas furnaces, each with its own microfarad rating suited to that specific motor's horsepower and design.
Capacitors fail in a few predictable ways. The internal dielectric film that stores electrical charge degrades chemically over time, a process that speeds up significantly with heat exposure, which is why outdoor AC capacitors baking in direct Texas sun fail far more often than an indoor furnace capacitor tucked away in a cabinet. As the film degrades, capacitance drifts outside the manufacturer's tolerance, typically plus or minus 6 percent of rated value, and the motor it serves starts struggling to start or run smoothly. In advanced failure, internal gas pressure builds enough to visibly bulge or even rupture the top of the can.
We test every capacitor with a capacitance meter rather than replacing on assumption, comparing the reading to the rated microfarad value and inspecting for physical bulging or leakage. This matters because capacitor failure symptoms, humming without starting, slow startup, tripped breakers, or a motor that hums and then shuts off on thermal overload, overlap heavily with symptoms of a failing motor or a weak contactor. Confirming the capacitor with a meter before replacing it prevents both unnecessary parts swaps and, just as importantly, catching a genuine motor problem that a new capacitor won't fix.
Replacement always matches microfarad rating and voltage rating exactly to the original part, we never substitute a close value, since an undersized capacitor won't provide adequate starting torque and an oversized one can actually overheat the motor winding it's paired with. For dual capacitors serving both a compressor and fan motor from one can, we also verify correct terminal wiring, Herm, Fan, and Common, before restoring power, since a miswired capacitor can damage a motor on its very first start.
Frequently Asked Questions, Capacitor Replacement
Need a Component Diagnosed or Replaced?
We test before we replace. Most parts are on the truck for same-day service.