HVAC Components We Repair & Replace, Georgetown TX
Motors & Fans
Diagnose and repair indoor blower motor failures, bearing wear, winding failure, and capacitor issues.
Replace failed indoor blower motors, we stock common motors for Carrier, Trane, Lennox, Goodman, and Rheem.
Lubricate blower motor bearings before they fail, catches motors that squeal before they burn out.
Clean blower wheels coated with dust and debris that reduce airflow and strain the motor.
Repair or replace condenser fan motors, outdoor fan failure causes compressor overheating on Georgetown's 100°F days.
Diagnose and repair outdoor condenser fan motor failures, common cause of AC shutdown in peak summer heat.
Replace cracked, bent, or imbalanced outdoor fan blades causing vibration and motor strain.
Capacitors & Contactors
The #1 Georgetown summer repair. Capacitors overheat and fail in sustained 100°F+ heat, fast, affordable fix.
Test capacitors before replacing, an out-of-spec capacitor causes the same symptoms as a failed compressor.
Replace failed run capacitors on compressors and fan motors, the most common summer AC component failure.
Replace start capacitors that provide the extra torque needed to start compressors on hot days.
Install hard start kits on aging compressors to reduce starting current and extend compressor life.
Replace pitted or failed contactors, the relay that connects power to the compressor and condenser fan.
Replace AC contactors with pitted contacts that cause intermittent power to compressor and outdoor fan.
Compressor Service
Diagnose compressor failures, not every compressor problem requires replacement. We test before recommending replacement.
Compressor replacement with full circuit flush, filter drier, evacuation, and recharge, done correctly to protect the new compressor.
Replace discharge mufflers that reduce compressor noise and protect the refrigerant circuit.
Install crankcase heaters to prevent refrigerant migration into compressor oil during cold Texas nights.
Replace failed high-pressure safety switches that protect compressors from dangerously high discharge pressure.
Replace low-pressure safety switches that prevent compressor damage from loss of refrigerant charge.
Furnace Components
Replace failed high-limit switches that shut furnaces down on overheating, essential safety component.
Replace faulty furnace control boards, we test all connected components first to confirm the board is the failure.
Repair or replace fan control switches that govern blower timing in older furnaces without electronic control boards.
Replace fragile silicon carbide or silicon nitride ignitors, the #1 furnace no-heat repair in Georgetown.
Replace or clean flame sensors that fail to detect the burner flame, causing furnace lockout.
Replace failed gas valves that prevent gas flow to burners, verified diagnosis before replacement.
Replace thermocouples on older standing pilot furnaces that fail to keep the pilot lit.
Replace tripped rollout switches, but also diagnose why flames rolled out, as this indicates a serious underlying condition.
Replace failed draft inducer motors in 80%+ efficiency furnaces, failure causes pressure switch trips and no-heat conditions.
Replace failed heating elements in electric furnaces, test all elements and sequencers before partial replacement.
Replace failed sequencers that stagger heating element startup to prevent circuit overload.
Replace cracked or blocked pilot tubing on older standing pilot furnaces and boilers.
Repair standing pilot assembly issues on older furnaces, thermocouple, pilot orifice, and gas valve.
Replace corroded or leaking main gas shutoff valves at HVAC equipment.
Outdoor Unit & Noise Components
Install compressor sound blankets to reduce outdoor unit noise, particularly useful in Georgetown's zero-lot-line neighborhoods.
Replace deteriorated equipment pads and isolation mounts that transmit vibration through slabs and walls.
Sorting Out Which Fan Motor Type You Actually Have
HVAC systems use several distinct motor technologies depending on the application, and correctly identifying which type you have is the first step in any fan motor repair, since diagnostic approach and available repairs differ between them. Shaded pole motors, an older, simpler design with lower efficiency and torque, still show up on some smaller fan applications and older equipment. PSC, permanently split capacitor, motors are the most common type on both indoor blowers and outdoor condenser fans across a large share of residential equipment still in service. ECM, electronically commutated motors, are increasingly standard on newer higher-efficiency equipment and use an internal electronic module to vary speed rather than running at one fixed RPM.
Each type fails somewhat differently. Shaded pole and PSC motors are mechanically simpler and more prone to straightforward bearing wear, winding overheating, or capacitor-related starting problems that a technician can diagnose with basic electrical testing, an amp draw reading, a capacitance check, and a resistance test across the windings. ECM motors add an additional failure point, the electronic control module itself, which can fail from moisture, power surges, or a bad communication signal from the furnace or air handler's main control board, sometimes causing symptoms like a motor that runs at the wrong speed or won't ramp up properly even when the mechanical motor is completely fine.
Our repair process starts by identifying motor type from the nameplate and confirming which specific symptom pattern we're dealing with, humming without starting typically points to a capacitor issue on PSC and shaded pole motors, while an ECM motor that spins slowly or erratically more often points to the control module or its connection to the main board. From there we test the relevant component, capacitor, winding resistance, control module signal, and either repair the identified fault or, when the motor itself has failed mechanically or electrically beyond repair, recommend replacement with a correctly matched part.
Fan motors, whether indoor or outdoor, are one of the most frequently serviced components across Georgetown's HVAC systems given how many hours they run through our long cooling season, and getting an accurate diagnosis of motor type and specific failure point before recommending a repair or replacement saves homeowners from unnecessary parts costs.
Frequently Asked Questions, Fan Motor Repair
Need a Component Diagnosed or Replaced?
We test before we replace. Most parts are on the truck for same-day service.